Search found 149 matches
- Fri Feb 16, 2018 7:49 am
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
I got it directly from AD, so I doubt it's a knock-off. I had 2 chips, both performed the same, but I burnt out one of them (and a pyboard at the same time) by mis-connecting the 12v power supply. I agree, it seems incredible that AD would sell an expensive chip like this ($20/each) for 20 years wit...
- Fri Feb 16, 2018 7:34 am
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
@pythoncoder: Thanks for the tip. I have stopped using the multimeter and instead inject a 500Hz sine wave on one of the pins and have an oscilloscope connected to the other. The signal generator and scope share the analog ground from the analog power supply. In the meantime, I have done extensive t...
- Thu Feb 15, 2018 12:53 pm
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
Thanks, but no bad connection... sigh
- Thu Feb 15, 2018 12:30 pm
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
Thanks!
I have added diodes to the cirucuit as suggested in the data sheet. I used 1N4004 diodes instead of 1N4001 or 1N5818 as suggested, no change. I also tired BAT46 diodes, but no change either...
I am really at a loss..
Thanks for the help in any case!
B
I have added diodes to the cirucuit as suggested in the data sheet. I used 1N4004 diodes instead of 1N4001 or 1N5818 as suggested, no change. I also tired BAT46 diodes, but no change either...
I am really at a loss..
Thanks for the help in any case!
B
- Wed Feb 14, 2018 11:42 am
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
@pythoncoder Yes, all the timing requirements are met and I have measured on the scope. I've continued to test this, now using a signal generator and the behaviors is exactly as I said: With analog supplies +/-7.6v normal correct behavior With analog supplies +/- 9v or +/- 11.35v or +/-12v, once som...
- Mon Feb 12, 2018 1:36 pm
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
Re: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
Thanks for that reminder, and I do pulse the PCLK to zero then back to one....
Any other ideas are of course welcome!
Cheers,
Bob
Any other ideas are of course welcome!
Cheers,
Bob
- Mon Feb 12, 2018 8:13 am
- Forum: General Discussion and Questions
- Topic: AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
- Replies: 20
- Views: 12905
AD75019 16x16 crosspoint switch/multiplexer cannot communicate via SPI
HI guys! I am trying desperately to get the AD75019 analog crosspoint switch to respond to bit vectors sent via SPI from a Pyboard but for the life of me I can not get it to do anything it should. The datasheet is here: http://www.analog.com/media/en/technical-documentation/data-sheets/AD75019.pdf M...
- Fri Dec 30, 2016 2:55 pm
- Forum: Announcements and News
- Topic: Multi-threading support, sponsored by Pycom
- Replies: 22
- Views: 161048
Re: Multi-threading support, sponsored by Pycom
Hi guys!
Any news on this? I'm waiting for it to come to the pyboard, as I just spent weeks debugging problems which would not have occurred if I had working threads...
Ciao,
Bob
Any news on this? I'm waiting for it to come to the pyboard, as I just spent weeks debugging problems which would not have occurred if I had working threads...
Ciao,
Bob
- Sun Oct 16, 2016 8:45 am
- Forum: General Discussion and Questions
- Topic: Pyboard noise
- Replies: 21
- Views: 19897
Re: Pyboard noise
@pythoncoder I can tell you the story of my all metal Asus UX303LN laptop. It is a very high end machine and very sweet. Except that the all metal housing gathers static electricity in huge quantities. So much so that I cannot put my hands on it while typing. I spoke to Asus about this and researche...
- Sat Oct 15, 2016 10:35 pm
- Forum: General Discussion and Questions
- Topic: Pyboard noise
- Replies: 21
- Views: 19897
Re: Pyboard noise
@chrismas9 Thank you so much for all the work you did in trying to help me!!! I still can't imagine that you could even find my board design, let alone study it carefully and comment it! And your post is a FANTASTIC reference that I will keep separately, like Dave said! I did the tests as you sugges...